rule grid

inside Rong

Hot air circulation drying oven TS101A-13L

An pretend use ruler inch

studio dimensions

Depth 2700mm * Width 2100mm * Height 2300mm

Overall dimensions

deep3000*wide2440+Control cabinet width210*tall2780+Motor height 270mm

Chassis load-bearing capacity

Channel steel production, surface laying. Science Weighing2 tons.

Internal storage rack in the studio:

empty box

Lord want skill technique ginseng number

On site environmental conditions

Temperature:5-40℃ Relative humidity: not greater than85% Suitable for indoor use

There is no strong vibration or airflow around No corrosive gases or chemicals present Non drying flammable and explosive materials

Equipment Composition

Composed of furnace body, hot air circulation system, electric heating system, intake and exhaust system, circuit control system, etc

electricity source

3N+PE 380V 50Hz

Temperature range for use

Room temperature~300 ℃ (adjustable arbitrarily)

temperature control accuracy

≤±1℃;

heating power

42KW

Heating time:

Under no-load conditions, the room temperature rises to 300 degrees Celsius for approximately 60 minutes

insulation thickness

90mmleft and right

stove body be unify knot constitute

structural form

Adopting a monolithic structure.Concentrated placement.

Opening method

Front of furnace bodydoubleOpen the door.(The door lock adopts chrome plated sheep horn handle and steel hinge)

Furnace shell

Q235After rust prevention treatment, cold-rolled steel plates are sprayed with acrylic self drying paint

Furnace inner liner

Q235cold-rolled steel sheet

Shell skeleton

Q235Rust removal and rust prevention treatment for channel steel and angle steel

Inner liner skeleton

Q235After rust removal and rust prevention treatment of angle steel, spray coatingW61Series of silicone heat-resistant paint

bottom plate

Q235After rust removal and rust prevention treatment of channel steel, spray coating851Moisture resistant coating.

thermal insulation material

Low thermal conductivity, high-quality high-temperature resistant aluminum silicate cotton

sealing material

Asbestos sealing strip sealing

drum wind be unify

air supply mode

Studio hot air supply method: horizontal strong pressure horizontal air supply on both sides simultaneously

Blower motor

High temperature resistant long shaft motor specifically designed for curing furnaces, with a noise level of65dBthe following

Blast power

1400 revolutions,1100W×4Platform, equipped4a12Inch impeller.

Installation position of motor

Set at the top of the furnace body

add hot be unify

Heater position

Inside the air ducts on both sides

electric heater

UThe font safe low load stainless steel electric heating tube is of reliable quality,3.5KW*12branch，

enter\\\\\\\\exhaust system

intake valve

Top fan base air inlet4A diameter of 60MM

exhaust valve

A manual exhaust valve is installed in front of the top2A diameter of 100MM (adjustable according to the required displacement). The supplier shall reserve flange interfaces and provide external exhaust pipes according to the actual situation in the workshop.

electricity control be unify

control manufacture cabinet

Adopting an independent control cabinet for control, the surface of the control cabinet is treated with spraying and painting. There are control boxes on both sides.

Temperature control device:

Digital display intelligent instrument XGQ-A2100FAutomatic temperature control, constant temperature and beltPIDAdjust. Control accuracy ±1℃.

Time setting device:

HS48S-99.99 timing device, with a maximum adjustable time of 9999H during actual setting. It can be manually/automatically switched on and off. The timer starts when the temperature reaches the set temperature, and the heating power is cut off when the constant temperature time is over. The fan does not stop rotating, helping to dissipate heat inside the box.

electrical components

Adopting domestic and foreign famous brands, such as Chint, Omron, etc

heating control

Suzhou Integrated ElectronicsSSRSolid state relays have contactless power regulation and use input stages with optoelectronic isolation,

TTLLevel compatible input, DC or pulse triggered, with no contacts and no mechanical moving parts,

No sparks, no movement noise, vibration resistance, long lifespan and other characteristics.

guarantee

protect

be

unify

match

place

●Automatically cut off the heating power supply.

● Motor and heating interlock control Start with the blower before heating to prevent the heater from burning out and causing accidents.

● Motor overload protection Prevent the motor from burning out and tripping.

● Short circuit protection for electric heaters Prevent electric heaters from short circuiting and burning out

● Control circuit protection Prevent short circuits in the circuit and prevent accidents

● circuit breaker Prevent overload and short circuit of the main circuit, which may cause accidents

● Power prevention after power outage Prevent damage to baked goods caused by increased baking time after power on

solid transform stove Appendix document and its it say bright

Yan color

Computer gray white

random file

Instruction Manual1copy/Taiwan Various instrument manuals1set/Taiwan