E103-W11 WiFi 6 and Bluetooth 5.1 protocol serial port to WiFi module-Global supplier

E103-W05无线数传WiFi模块 wifi 6无线模块
wifi 6无线模块 (1)
主图4
wifi 6无线模块 (3)
wifi 6无线模块 (4)
wifi 6无线模块 (5)
wifi 6无线模块 (6)
wifi 6无线模块 (7)
wifi 6无线模块 (8)

RF application	Parameter values	notes
Working frequency band	2400MHz~2480MHz	Support ISM frequency band
Transmission power	19.5dBm~20.5dBm	Software adjustable, users need to develop and set it themselves
receiver sensitivity	-87 dBm	Air speed 500kbps
Wi Fi version	IEEE 802.11 b/g/n/ax	modulation technique
air rate	150Mbps
Blocking power	10dBm	The probability of burning is relatively low when used at close range
Reference distance	300m	Clear and spacious, antenna gain0 dBi, onboardPCBAntenna.

Parameters	performance			notes
Parameters	minimum value	Typical values	Maximum value	notes
Working voltage (V)	3	3.3	3.6	≥ 5V ensures output power, exceeding 5.5V permanently burns out the module
I/O voltage	-0.3	-	3.6	Exceeding 3.6V may permanently damage module I/O
Communication level (V)	-0.3	3.3	3.6	There is a risk of burning out when using 5V level
Working temperature (℃)	-40	-	+85	Industrial grade design

Hardware parameters	Parameter values	notes
Packaging method	Surface mount type	-
Interface method	Stamp hole	Distance of 2.0mm
communication interface	UART serial port	TTL level
External dimensions	16*24 mm	-
Net weight	1.3g	0.1g
Radio Frequency Interface	IPE/Stamp Hole	Equivalent impedance of approximately 50Q

wifi 6无线模块引脚

Pin number	Pin Definition	I/0	Function and usage instructions
1	U0_TXD	0	AT serial port, module's TX, connected to external TTL RX
2	U0_RXD	l	AT serial port, module RX, connected to external TTL TX
3	PWM	I/0	GPI0_NUM_4， It can be used as a regular GPI0 through the SYI0 series instructions.
4	MIS0	I/0	GPI0_NUM_3， It can be used as a regular GPI0 through the SYI0 series instructions.
5	M0SI	0	Debugging serial port of E103-W11, module L0G_TX, connected to external TTL RX
6	CS	l	Debugging serial port of E103-W11, module L0G_RX, connected to external TTL TX
7	CLK	I/0	GPI0_NUM_0， It can be used as a regular GPI0 through the SYI0 series instructions.
8	GND	-	Ground wire, connected to the power reference ground
9	GND	-	Ground wire, connected to the power reference ground
10	RST	I	Chip reset triggers input pin, low level is valid
11	ADC	I/0	GPI0_NUM_20， It can be used as a regular GPI0 through the SYI0 series instructions.
12	I01	I/0	GPI0_NUM_1， It can be used as a regular GPI0 through the SYI0 series instructions.
13	I02	I/0	GPI0_NUM_2， It can be used as a regular GPI0 through the SYI0 series instructions.
14	DATA1	I/0	GPI0_NUM_23， It can be used as a regular GPI0 through the SYI0 series instructions.
15	DATA0	I/0	GPI0_NUM_22， It can be used as a regular GPI0 through the SYI0 series instructions.
16	H_CLK	I/0	GPI0_NUM_13， It can be used as a regular GPI0 through the SYI0 series instructions.
17	GND	-	Ground wire, connected to the power reference ground
18	CMD	I/0	GPI0_NUM_21， It can be used as a regular GPI0 through the SYI0 series instructions.
19	DATA3	I/0	GPI0_NUM_25， It can be used as a regular GPI0 through the SYI0 series instructions.
20	DATA2	I/0	GPI0_NUM_24， It can be used as a regular GPI0 through the SYI0 series instructions.
21	WAKE	I	The chip wake-up triggers the input pin, and the low level is effective. When using it, a resistive capacitive reset pull-up is required
22	I03	I/0	GPI0_NUM_16， It can be used as a regular GPI0 through the SYI0 series instructions.
23	GND	-	Ground wire, connected to the power reference ground
24	VCC	-	power input

Product manual

Tool software

Introduction to Yibaite

Online purchase

Yibaite Official Taobao Store】:

To Zhe Yi Bai Te Exclusive Store:

Alibaba:

Bulk procurement/customized products

Sales Hotline: 7x24 hour sales service hotline

[Contact email]: sales@cdebyte.com

Technical Consultation

Online submission:

[Contact email]:support@cdebyte.com

technologyapplication

Frequently Asked Questions

★Question:Can two WIFI radios communicate directly with each other; How to configure it if possible.

Answer:sure; The manual provides detailed instructions on how to set up APSSTATION, including how to connect one as a Station and the other as an AP.

★ Question: Does it support MQTT or Azure? If not, is there any way to do it?

Answer:MQTT and Azure belong to the upper layer protocol references of the Internet of Things, and customers can implement the protocol content on E103-W02

★Question:May I ask if the module pins are compatible with ESP-12? How big is Flash?

Answer:Our E103-W01 pin is compatible with ESP-12F, and our external flash size is 1MB.

★ Q: Is it possible to implement data transmission from one hundred modules on a device to a server?

Answer:tolerable.

★Question:What is the reason why the WIFI module cannot ping the external IP address when the module is connected to the router and the router is connected to the external network?

Answer:Cannot ping the external network.

★Question:How long can the maximum sleep time be set before the module is automatically awakened, for example, can it be set to 4 hours before waking up?

Answer:It can meet the requirement of 4 hours wake-up time for configuration, but the longest time has not been tested. You can test it yourself.

★Question:How to configure a module to enter a low-power state and wake up the module on a scheduled basis?

Answer:The manual contains relevant AT command setting methods and instructions, which belong to timed wake-up, but not periodic.

★Question:I cannot modify the module name. After successfully modifying it, I used the AT command to check if it was the name I wanted. However, when I scanned it with my phone, the name was still "CDEBYTE". After powering it on countless times, I found that the name had not changed. This module cannot be scanned by Bluetooth modules from other companies, nor can it be scanned by WIN10 computers. It can only be scanned by my Xiaomi phone. I have tried both single role and multi role modes, but this module cannot be scanned.

Answer:1. Computers need to have BLE function to scan our devices. Generally, computers use classic Bluetooth, which cannot be scanned; 2. Recommend using the "BLE Deng" app software for testing; 3. Please ensure that the power supply is sufficiently stable; 4. Our E74 is currently in the Xiaomi series of smartphones; 5. The Bluetooth name can be modified, and the app uses the testing software lightblue; It is recommended to use lightblue and BLE assistant for testing software IOS, and BLE deng for Android.

★ Question: In UDP mode, it is possible to connect, but communication is not possible. What is the reason for not receiving data when sending?

Answer:You can first check if the port information configured for UDP socket matches that of the sender; Try sending data to each other. Early versions require customer service to send data to the server first. It is recommended to upgrade to the latest version V1.5 based on our customer information to solve the problem.

★ Question: Do you have performance testing data for the module?

Answer:We tested EVM, frequency accuracy, harmonic distortion, power adaptability, and standing wave ratio. The throughput of WiFi has not been tested.

★ Question: What is the AT command for sending data? I couldn't find it in the manual

Answer:In transparent transmission mode, simply send the data directly. No instruction required.

★ Question: Can the second pin on the module, which is the ADC input pin, be used to detect battery voltage?

Answer:Can be used to detect voltage, with a detection range of 0.0V~1.0V voltage; Our user manual provides detailed instructions, please refer to the user manual.

★ Question: Is the LED indicator light on the module a power indicator light or a signal indicator light?

Answer:Intermittent Double Flashing: The module cannot connect to the AP access point. Intermittent Single Flashing: The module has connected to the AP access point but cannot connect to the TCP server. Off: The module has connected to the AP and the server, which is the status indicator light; Please refer to the product manual for details.