Product Description

7 × 6 hammer mill

7×6 Hammermills

Model 7 × 6

These hammer mills have a 0.40 cubic foot (20 pound) feed hopper with a lid and manual feed control. The device has a cast iron ductile iron crusher housing that is hinged and locked for quick maintenance. If the stop button is not pressed, the latch sensor will cut off all power. The rotor pendulum and all 3/16 inch sieve plates have undergone heat treatment and hardening. These rotor components are reversible to extend the lifespan of the hammer. The sieve plates all have circular perforations. The device comes with 2 containers; The pond has a capacity of 10 pounds and weighs 35 pounds, and is sealed at the outlet when crushed. Standard configuration includes 2HP TEFC 230/460V/3/50-60 Hz electric motors and NEMA 12 electromagnetic starters.

Model 201XL

• The covered feeding hopper with a capacity of. 40 cubic feet (20 pounds) has a gate for manual feeding control.
• The casing of the ductile iron crusher is quickly connected through hinges and latches.
• If the stop button is not pressed, the opened latch sensor will cut off all power. Before restarting the machine, please press the reset button.
• The rotor pendulum and all 3/16 inch thick sieve plates have undergone heat treatment and hardening.
• The rotor component is reversible (connected end-to-end) to extend the service life of the hammer.
• The sieve plates all have circular perforations. The diameters of the raw material holes are 1/16 inch, 3/32 inch, 1/8 inch, 3/16 inch, 114 inch, 3/8 inch, and 1/2 inch.
• Two containers are provided - with capacities of 10 pounds (4.5 KG) and 35 pounds (16 KG). Seal it at the discharge port when crushing.
• Equipped with 2 horsepower, TEFC， 230/460 volts, three-phase 60 hertz motor and Nema 12 magnetic starter. The starter provides overload protection for the motor and 120 volt control circuit. Provided approximately 10 feet of four core rubber sheathed cable. The backup power line is 20 volts, three-phase, 60 Hz.
• The crusher is installed on four 21/2-inch diameter casters.
• Capacity: Using a sieve with a diameter of 3/16 inch, it can produce 1000 pounds of coal per hour. Perforation using 1/16 inch diameter at a rate of 500 pounds per hour. Suggested for crushing 2-inch and smaller materials.
• Rotor speed: approximately 3450 RPM
• Power requirements: The backup wire is 230 volts, three-phase, 60 hertz, and 7 amps. Other available electrical specifications, including those for hazardous locations.
• Shipping weight: 325 pounds

Holmes 10 x 15Hammer mill

Holmes 10 x 15 Hammermill

Sherlock Holmes 10 x 15 Hammermill

The Holmes hammer mill is a lightweight to medium-sized shock-absorbing crusher designed specifically for coal, but cannot be used with materials that are harder than medium hard limestone (Mohs hardness of 5). These 10 × 15 hammer mills are capable of reducing -6 inches of material to negative 10 mesh at a rate of 2500 pounds. Use 3/16 inch sieve plates per hour. Using a larger 3/8-inch sieve plate will increase the capacity to 4000 pounds. Reduce the material from -6 inches per hour to -4 mesh.

• The covered feeding hopper has a capacity of 1.6 cubic feet (70 pounds) and is equipped with a manual feeding control door.
• The casing of the ductile iron crusher is quickly connected through hinges and latches.
• The opened latch sensor will cut off all power supply. If the stop button has not been pressed yet, please press the reset button before restarting the machine.
• The rotor pendulum and all 3/16 inch thick sieve plates have undergone heat treatment and hardening.
• The rotor component is reversible (connected end-to-end) to extend the service life of the hammer.
• All sieve plates have circular perforations. The diameters of the raw material holes are 1/8 ", 3/16", 1/4 ", 5/16", 3/8 ", 1/2", 3/4 ", and 1".
• A 1.5 cubic foot container can hold approximately 70 pounds of coal. Seal it to the discharge port when crushing.
• Equipped with 7.5 HP, TEFC, 230/460V three-phase, 60Hz motor and Nema 12 magnetic starter. The starter provides a 120 volt control circuit and overload protection for the electric motor. Provide a four core rubber sheathed cable approximately 10 feet long to connect to a power source.
• The crusher is installed on four 4-inch diameter casters.
• Capacity: A machine with a diameter of 3/8 inch can generate a weight of 4000 pounds per hour. Perforated. Screen plate weighing 2500 pounds (using 3/16 inch diameter). Screen. Suggest crushing materials 6 inches or smaller to negative 4 mesh.
• Rotor speed: 1260 RPM, interchangeable "V" belt pulley -2360 RPM
• Power requirements: The backup wire is 230 volts, three-phase, 60 hertz, 21 amperes. The machine can be equipped with other electrical specifications and hazardous locations.
• Sound level: Air -75-77 dBA
• Shipping weight: 840 pounds (380 kilograms)

Hammer millSeries G

Description:

The G series hammer mill is a shock-absorbing crusher designed for materials that are not higher than medium hard limestone (Mohs hardness 5). These hammer mills have heavy-duty frames and racks, wear-resistant liners, anti friction bearings, doors for easy inspection of internal parts, easily replaceable hammers, easily replaceable discharge screens, as well as various hammer types and screen sizes, with screen sizes as small as 1/16 inch openings. The capacity shown is based on 3-inch feed and product 100% -4 mesh. Optional equipment includes steel beam mounting base, motor, driver, protective device, bracket, and hopper. The equipment is coated with primer and coated with a layer of enamel.

Rotating assembly:

Our technical sales engineers will assist you in guiding you on how to correctly select the appropriate rotor type to meet your special restoration needs. Popular combinations of industrial rotors and hammers:

（1) A chisel and hammer for chopping wood and fiber materials;
（2) Hard impact hammer;
（3) Crushing rocks and minerals using a T-shaped or bullhead hammer and ultimately crushing them;
（4) Circular hammer, used for slow granulation and controlling fine powder as needed;
（5) Remove the rotor of the hammer. Please note that the position of the bearing housing extending from the rotor is good, while the one removed from the grinding chamber is good. Hot materials can be easily processed.
（6) A rigid hammer rotor with a 6-point hammer.

The G series hammer mill has a locking plate installation function for hammer pins, bolts, and rods, which can provide you with many advantages, such as preventing end movement, preventing hammer pin end wear, and preventing shell damage (due to damaged nails and worn pin nuts). It allows for replacement and replacement production time that is 1/10 of the original.

To control dust, it is approximately necessary to250 CFM of air.Capacity based on3-inch feed, -4 mesh product.
The maximum particle size of the crusher is4 inches.